Author Topic: 1/35 scale modern zombie hunters (UD 26.05 - finally online) (Read 29943 times)

Not yet dead · « **Reply #15 on:** October 02, 2013, 07:13:06 AM »

The space needed is Not that Bad, I also only have a small table and no dedicated room

I am making two 5 mm foamboards each with a size of 80cm x80cm, these are devided into 40mm squares, giving me 400 squares per board, more than enough space for atleast 10 buildings plus roads. Most buildings will be 6x5 or 9x7 squares.

And if my plans work out I can lay them flat due to using magnets!! (still in wip Phase).
If not One Box will Hold them all.

In this scale I can still fit about 80-100 Zombies on the board, and instead of 20 vehicles I can still use 5-7 plus odds and ends.

Of course you can't go for Mega hordes in this scale, but it looks quite impresive, and with my old eyes I can see them better

Cheers

Slayer · « **Reply #16 on:** October 02, 2013, 07:16:14 AM »

great work so far

Not yet dead · « **Reply #17 on:** October 02, 2013, 07:31:07 AM »

Slayer - thanks....just had a Set back with my first 3D model, to say it was bad is an understatement!!! Oooohhh this is Fun

Slayer · « **Reply #18 on:** October 02, 2013, 07:33:36 AM »

can only get better then eh

Not yet dead · « **Reply #19 on:** October 02, 2013, 07:41:02 AM »

Oh god yes, 100% better than crap...

Not yet dead · « **Reply #20 on:** October 14, 2013, 02:57:43 PM »

I´ve got my first 6 x 3D Renderings finished and my first 3d Printed figure...

100% better than the first trial...

Now I´m getting a couple of trial prints done in other materials, see if we can get more/smoother detail in there..

Sorry that the print photo is so crap...I will try and give it a black wash tonite at home, and then take another.

any resemblance to characters, living, (un)dead or fictional, is purely coincidental.

Cheers
NYD

mindfad · « **Reply #21 on:** October 15, 2013, 10:26:08 AM »

is that print of your home 3d printer or through shapeways. Howd did the weapon sprue come out?

Not yet dead · « **Reply #22 on:** October 15, 2013, 10:34:56 AM »

@ mindfad - not shapeways, but a local 3D company. We are still experimenting with the processes at the moment, but we are getting there.

Weapons came out ok (as you can see)..but the scale of the Cricket bat, the Katana shaft and the baseball bat were a bit off. These have been corrected and
are going out for the next trial print next week.

Cheers
NYD

Not yet dead · « **Reply #23 on:** October 22, 2013, 06:44:55 AM »

I have finally got a good 3D print for one of the survivors, and I slapped a bit of paint on her.

It´s still not 100% how I want it, but I´m getting there

C & C welcome

Cheers
NYD

Not yet dead · « **Reply #24 on:** October 22, 2013, 06:46:13 AM »

forgot the piccys

Not yet dead · « **Reply #25 on:** November 04, 2013, 07:00:46 AM »

inbetween doing the 3D print I found time to paint up a commercial figure.

"run, Jimmy run"....

C & C welcome

NYD

HerbyF · « **Reply #26 on:** November 04, 2013, 07:30:21 AM »

Horror Clix does a 50 foot Ex Girlfreind. She would size up nicely for a zombie or maybe even a survivor.

Not yet dead · « **Reply #27 on:** November 04, 2013, 07:36:14 AM »

an Ex Girlfriend is horror enough, but at 50 ft....sh*t...run Jimmy runaway.....

zizi666 · « **Reply #28 on:** November 04, 2013, 12:38:37 PM »

Quote from: Not yet dead on November 04, 2013, 07:36:14 AM

an Ex Girlfriend is horror enough, but at 50 ft....sh*t...run Jimmy runaway.....

Hear, hear !
Exes are poison. better to stay away from them.

jamii · « **Reply #29 on:** November 10, 2013, 10:07:54 PM »

um, how tall is 1/35 scale in millimeters? I mean to top of head, and to eye level.

News:

Donate

We Appreciate Your Support

Recent

Author Topic: 1/35 scale modern zombie hunters (UD 26.05 - finally online) (Read 29943 times)

Related Topics