Lead Adventure Forum
Other Stuff => Workbench => Topic started by: Willypold on 28 May 2011, 06:28:50 PM
-
Ok, I bought one of the new GW Finecast models today, a Pyrovore for my Tyranids. I don't like metal miniatures and really prefer plastics. The model looks great, it was really simple to clean up and everything, but both of my glue variants failed miserably. My trusty contact glue couldn't get a grip on things, and the super glue I have only managed to stick the tube to my work desk - no personal parts attached to themselves or any loose objects this time, fortunately!
So. What to do? What have I missed? Bad super glue? Special cleaning procedure? Wrong incantations read?
-
Strange - I used a more or less generic modelling thick liquid CA glue, and it worked like a charm, both when I had to match resin-to-resin and resin-to polystyrene (the base).
It may be that your glue has gone off, or that the climatic conditions weren't great (too humid or something, has affected me before).
Maybe try another brand of superglue. Plastic glue won't work at all.
-
cyanacrilic glue should work well, but i think it depends to the type of glue and resin...
a quite common problem is related to the sweat coming of the resin, but i seriously hope that the GW resin is a good quality one! (being such expensive!)
-
It might be the mould release on the rein. Wash everything in soap thoroughly first.
Superglue should do the job.
If not Im sure GW will be along any minute to sell you a £30 tube of "special citadel glue!" :)
-
Superglue every time. I've worked with all kinds of resin, and picked up one of the new Finecast models. As long as you've got good contact points on the components, any thin, strong superglue should stick instantly. Good luck!
-
If not Im sure GW will be along any minute to sell you a £30 tube of "special citadel glue!" :)
lol lol lol
it's funny because it's true! :)
-
Considering the cost of the glue I tried and what I usually expect to pay for super glue it may be that the glue is sub-par... I'll see if I can get hold of another brand tomorrow. And thanks for the advice!
-
I don't mean to laugh at your misfortune but after publicly saying you picked up a pyrovore that you were more than happy with cast quality wise I think you tempted fate a little too much.
:)
Yeah wash the model just in case it is a mould release problem, though to be honest for super glue to not stick at all it would likely have to be a noticeable amount of the release agent to the extent that it looked or felt greasy to the touch.
Which would lead me to think the glue is the problem ... unless GWs new stuff has an evolved version of the glue repelling qualities their metal miniatures seemed to display time and again.
:?
-
I've seen comments about bad castings and such, and was half expecting something really bad, but in this case there was not a single airbubble, nothing miscast, and crisp detailing throughout.
It would be interesting to find out the frequency of bad castings to good, though.
Right now I'm quite happy with my new little beast - which makes the old Biovores look like puppies next to it!
-
Yeah I'd be interested in finding that out too, naturally a lot of people will only make posts about problems they have had with the new models rather than if everything was fine so certainly at this early stage the negatives will probably be the more commonly reported.
-
I once had the same problem but I hadn't washed the model first to remove the mold release agent... ::)
-
If not Im sure GW will be along any minute to sell you a £30 tube of "special citadel glue!" :)
I don't know, their $5 CAD super glue works wonders, and is far more viable option than any other uncommon glue in town here.
-
I remember reading someplace that GW boasted of not using a release agent at all, therefore washing not necessary?
Not that I am in any way interested in this product line, looks like a fast way to ruin GW for good. I'd say RIP GW. Like Rackham before them, it's almost as if they're actually looking for a way to make suicide. Are they abandoning plastics too, or is this supplementing plastic production?
-
Are they abandoning plastics too, or is this supplementing plastic production?
AFAIK they're moving to resin for single/ small run minis, and sticking with plastic for units and large kits, but dropping metals.
-
Ok, that makes more sense I guess, provided they can actually produce decent casts. So far it's not looking good. So this resin is not hazardous to your health then, unlike all other resins? ::)
-
Actually, so far it really is looking good. I've had the chance to look at several of the models at the local GW store. They are aware of the existance of miscast models, and the policy is to replace any bad ones - which actually happened when I was at the store today - a miscast marine model was replaced, no hassle, no problems.
Point is, you don't need to accept bad products. And the models I've seen look great - crisp detailing, easy to work with, and now I've also had a tutorial about assembling them - washing IS necessary, by the way...