*

Recent Topics

Author Topic: Sticking a woodland scenics flock matt to MDF  (Read 1621 times)

Offline mcmatt

  • Student
  • Posts: 13
Sticking a woodland scenics flock matt to MDF
« on: 24 April 2017, 07:35:38 PM »
Hey all,

Looking for suggestions.

I have one of these (http://woodlandscenics.woodlandscenics.com/show/Item/1RGVM-GG/page/1) that I plan on sticking to an MDF/Foam board. The board will be flat and this was just a shortcut to avoid texturing and flocking the board.

Would Mac Tac adhesive paper or glue work best? Any other suggestions?

Thanks for any tips. Promise to report back with any interesting learnings.

Offline snitcythedog

  • Supporting Adventurer
  • Scatterbrained Genius
  • *
  • Posts: 2885
    • Snitchys blog
Re: Sticking a woodland scenics flock matt to MDF
« Reply #1 on: 25 April 2017, 11:01:00 PM »
Why not super 77 spray adhesive?  Easy to find in the states.  I am not sure over here in the UK becasue I have not looked.  Gives you a permanently tacky surface.  Just spray the wood, then work from the edges and smooth the mat over it.  My two cents.
Snitchy sends
A bottle of scotch and two aspirin a day will greatly reduce your awareness of heart disease.
http://snitchythedog.blogspot.com

Offline jon_1066

  • Mastermind
  • Posts: 1175
Re: Sticking a woodland scenics flock matt to MDF
« Reply #2 on: 26 April 2017, 10:00:09 AM »
I used Copydex (not sure the what the US alternative is) but I would advise against doing it.  It starts shedding its flock almost immediately and starts going bald.

Offline SotF

  • Mad Scientist
  • Posts: 962
  • Shadow Of The Future
Re: Sticking a woodland scenics flock matt to MDF
« Reply #3 on: 26 April 2017, 10:52:48 AM »
Not sure about the specifics of the woodland scenics mat, but I've used various railroad ones in various projects over the years.

A spray adhesive tends to work best if it's paper backed.

Also, if the board is going to be a flat one, get a dowel longer than the board is wide (A cheap one from the hobby store works well, or even a pipe piece you might have). Open your mat up and roll it, flock side in, on the dowel before putting it in place. When you're ready to mount it, the dowel allows you to have a nicer, even pressure on the mat as you lay it out and is less likely to have bubbles and other issues when it goes down.

Offline DELTADOG

  • Mad Scientist
  • Posts: 691
  • The two-handed G.E.C.K
Re: Sticking a woodland scenics flock matt to MDF
« Reply #4 on: 27 April 2017, 03:03:43 PM »


Sounds weird but works the best on both materials! Garanty of No-warping inclusive!

Take care to use the silver one, the red one is not tough enough to hold it in place for the lifetime of the module.

Offline Norm

  • Supporting Adventurer
  • Mastermind
  • *
  • Posts: 1292
    • Blog for wargaming in small places
Re: Sticking a woodland scenics flock matt to MDF
« Reply #5 on: 27 April 2017, 10:10:55 PM »
I used PVA and ruined the mat. It air-bubbled and when dry, did not stick properly. I notice in the hobby store that Woodland Scenics do a glue for this...  but it looked like PVA, so I never bought it. I then tried double side tape, but could not get the mat taught enough. At that point I gave up!

 

Related Topics

  Subject / Started by Replies Last post
20 Replies
12108 Views
Last post 03 September 2010, 11:55:17 AM
by Dr. The Viking
11 Replies
4064 Views
Last post 09 January 2012, 02:15:16 PM
by FramFramson
10 Replies
4721 Views
Last post 13 June 2015, 03:12:30 PM
by ivor13
4 Replies
1717 Views
Last post 01 November 2015, 08:31:19 PM
by AndrewBeasley
9 Replies
686 Views
Last post 05 May 2025, 06:44:59 PM
by Rick